Again which of those you go with will depend on a few things. Check out the link below to see which base is best for you. Sintered bases require more waxing. This means a couple of things:. But if you neglect waxing a sintered base it will be slower than an unwaxed extruded base. So, in order to maintain the benefits of having a sintered base it needs waxing more often. How often that is will depend on some other factors as outlined below.
Naturally if your board is used more often then you will need to wax more often — if it used less often it will need waxing less often. You lose wax as you ride so this is logical. The wax also acts a layer of protection for the base of the board — so if you are riding in hard or icy conditions or there is a low snow level, and you have the potential to hit exposed rocks, roots etc, then you will want to wax more often to maintain a protective layer.
The temperature will also play a part in how quickly you lose wax. On hotter days the wax will wear down quicker. If you do have that need for speed then wax more often but if you prefer a slightly slower board for whatever reason then you could hold back on the waxing. Ideally those not wanting too much speed would have an extruded base but you may already have a sintered base fortunately most beginner and freestyle boards do have extruded bases.
Check out this video for a quick overview of how you can tell if your board needs waxing. Another way to check is to if you run your fingernail over the board and it does not collect wax then you may need to wax. For maximum performance on a sintered base you probably want to wax every full days of riding. If you can make that sacrifice you can wax less often.
But you still probably want to wax at least every days of riding depending on the factors above conditions you ride in, how fast you want it. You have a little bit more leeway with extruded bases. So you can get away with doing it less often. If you want to get the most out of your extruded base then again every days of riding will maximize performance.
Thanks for checking out this page and I hope it has helped you to decide how often you will wax. Remember that it depends on your own personal circumstances. If you have any comments, opinions or questions please feel free to leave them in the comments section below.
Get the 7 step email series plus other relevant snowboarding emails, review releases, promotions, and information from time to time. We take your privacy seriously. No spam. See our privacy policy here. Nate is passionate about and loves learning new things everyday about snowboarding, particularly the technical aspects of snowboarding gear. What will I need? Structuring brush. Before the iron goes anywhere near your base, make sure to loosen off or fully remove your bindings.
Clean the base. Make sure that any old wax and dirt is removed from the base so that the fresh wax can be absorbed properly.
This can either be done by using a base cleaner and cloth, or by the hot scrape method. A hot scrape involves using an iron to apply a thin layer of hot wax and then immediately scraping it off while the wax is still warm in order to get rid of any grime from the pores.
Once finished, wipe over the base with a cloth to remove any remaining residue. Pick your wax. Melt the wax. Warm up the iron to a medium heat and then hold the wax against the iron until it starts to melt the wax at a slow drip. What will I need? Structuring brush. Before the iron goes anywhere near your base, make sure to loosen off or fully remove your bindings.
Clean the base. Make sure that any old wax and dirt is removed from the base so that the fresh wax can be absorbed properly. This can either be done by using a base cleaner and cloth, or by the hot scrape method. A hot scrape involves using an iron to apply a thin layer of hot wax and then immediately scraping it off while the wax is still warm in order to get rid of any grime from the pores. Once finished, wipe over the base with a cloth to remove any remaining residue.
Pick your wax. Melt the wax. Warm up the iron to a medium heat and then hold the wax against the iron until it starts to melt the wax at a slow drip.
0コメント